Every Soulnote amplifier shares one philosophy: completely non-NFB circuits (no global negative feedback), tuned by ear rather than by measurement, and built with floating, vibration-conscious construction. The three integrated amplifiers below the flagship A3 differ mainly in power, scale and features. Here's how to choose.

The short answer: the A-0 ver.2 is a 10-watt purist amplifier for efficient speakers and headphones. The A-1 ver.2 brings 80 watts of fully balanced power, enough for most speakers and rooms. The A-2 ver.2 has the same rated power but a far bigger, current-first design for demanding speakers, and doubles as a power amplifier.

Side by side

A-0 ver.2 A-1 ver.2 A-2 ver.2
Price in Canada $4,490 $5,990 $12,990
Power (8 ohms) 10 W per channel 80 W per channel 80 W per channel
Power (4 ohms) See product page 120 W per channel 160 W per channel
Circuit Full discrete non-NFB, single push-pull, four-stage Darlington Perfectly balanced discrete non-NFB Non-NFB, hFE-matched parallel push-pull TO-3P output, four-stage Darlington
Volume control See product page Relay-switching balanced attenuator Relay-switching balanced attenuator
Headphone amplifier Yes, 3.0 W × 2 into 32 ohms See product page See product page
Extra modes Pre-out with High/Low mode (RCA and XLR) No Four modes: integrated, bi-amp mono integrated, stereo power amp, bi-amp mono power amp
Weight About 8 kg About 10 kg About 20 kg
Finishes Premium Black or Premium Silver Black or Silver Black or Silver

All three are hand-built in Japan. Models not in stock in Canada are special order and usually ship in 10–21 business days.

Soulnote A-0 ver.2: the purist

The A-0 ver.2 takes the thinking of the flagship A3 and distils it into Soulnote's most accessible integrated: a full discrete non-NFB design with a single push-pull output stage. Its 10 watts per channel are fast and clean, with frequency response reaching 350 kHz and a 115 dB signal-to-noise ratio. It also has a proper headphone amplifier (3.0 W per channel into 32 ohms) and a pre-out you can switch between High and Low modes on RCA and XLR, so it can later become a preamp.

Choose it if: your speakers are efficient and your room is small to medium, or you listen a lot on headphones.

Soulnote A-1 ver.2: the all-rounder

The A-1 ver.2 is the most popular route into Soulnote. It delivers 80 watts per channel into 8 ohms (120 W into 4 ohms) from perfectly balanced, discrete non-NFB circuits, with paired low-Cob, high-Ft output transistors and a relay-switching balanced attenuator instead of a conventional volume pot. Frequency response runs from 3 Hz to 300 kHz with a 110 dB signal-to-noise ratio.

Choose it if: you want the Soulnote sound with enough power for most speakers and rooms. For a digital source, the D-1N ver.2 DAC is the natural partner.

Soulnote A-2 ver.2: the current-first heavyweight

On paper the A-2 ver.2 has the same 80 watts into 8 ohms as the A-1, but it is a very different amplifier. Its parallel push-pull output stage uses high-speed TO-3P transistors matched by hFE, driven by a four-stage Darlington, and a large non-impregnated toroidal transformer deliberately run at lower voltage so it can deliver instantaneous current into difficult speakers. Into 4 ohms it doubles to 160 watts. Construction goes further too, with connectors removed from the signal and power paths, a floating top cover and an unsecured circuit board.

It is also four amplifiers in one: a stereo integrated, a bi-amp mono integrated, a stereo power amplifier, or a bi-amp mono power amplifier. In power-amp mode it bypasses the selector and volume entirely, so it can grow with your system.

Choose it if: your speakers are demanding or low-impedance, such as the Guru 28, Ophidian Incanto or Ophidian Ffion, or you plan to bi-amp later. The D-2 ver.2 DAC is its matching source.

And the A3?

Above these three sits the flagship A3, which combines Soulnote's P-3 preamplifier and two M-3 monoblocks in one chassis, with 120 W per channel into 4 ohms and full left/right ground separation.

Frequently Asked Questions

Is 10 watts enough?
With efficient, easy-to-drive speakers in small to medium rooms, yes. The A-0 ver.2's fast non-NFB design sounds bigger than its rating. For harder-to-drive speakers or larger rooms, choose the A-1 ver.2 or A-2 ver.2.

The A-1 and A-2 are both 80 watts. Why does the A-2 cost more than twice as much?
Because watts into 8 ohms don't tell the whole story. The A-2's parallel output stage and much larger power supply deliver far more current into low-impedance loads (160 W into 4 ohms versus 120 W), and it adds four amplifier modes, including use as a pure power amplifier.

What does non-NFB mean?
No global negative feedback. Most amplifiers use feedback to lower measured distortion; Soulnote leaves it out because it believes feedback costs music its timing and life. Read the Soulnote design philosophy.

Where can I buy Soulnote in Canada?
From Audionation, Soulnote's exclusive Canadian distributor, with shipping across Canada, or from an authorized Audionation dealer. See the full Soulnote range.

More from Notebook

View all

  • by Audionation

Building a Complete Unitra System: Three Matched Setups

Three complete Unitra hi-fi systems, from an all-in-one vinyl starter to the dual-mono flagship, with what each component does and Canadian prices.

Read moreabout Building a Complete Unitra System: Three Matched Setups

  • by Audionation

Which Guru Speaker Is Right for Your Room? Q10, 8, 12, 20 and 28 Compared

Guru's five loudspeakers compared: size, bass extension, room size, stands and Canadian prices, plus why every Guru is designed to sit close to the wall.

Read moreabout Which Guru Speaker Is Right for Your Room? Q10, 8, 12, 20 and 28 Compared

  • by Audionation

Soulnote A-0 vs A-1 vs A-2: Which Soulnote Integrated Amplifier?

Soulnote's three integrated amplifiers below the flagship A3 compared: power, design, features, Canadian prices and which speakers suit each.

Read moreabout Soulnote A-0 vs A-1 vs A-2: Which Soulnote Integrated Amplifier?